#Ifixit a1286 logic board how to
#Ifixit a1286 logic board cracked
#Ifixit a1286 logic board install
#Ifixit a1286 logic board pro
#Ifixit a1286 logic board Bluetooth

I already did it twice because the screen had lines on when I finished, and I also managed to inadvertently disconnect the on/off button and not reconnect properly. Then I just put the screws in however they came to me. I do remember one didn’t stick to the screwdriver, and I actually dropped this one into the iPhone and then on the mottled carpet when I shook it out, but found it after a long search. Makes sense now that the top left one is longer, I got a bit frustrated trying to get that one in, and ended up putting it in last so the others would hold the plate in position. So I didn’t know the screws were different sizes, they all looked pretty teeny tiny to me. I watched the YouTube video on my smart TV while doing the repair. I mostly access the internet on my phone as my laptop is super slow. I didn’t have access to this guide when taking my phone apart. Did you check / note down the position of the screws at dis-assembly?Įek.

#Ifixit a1286 logic board install

Did you install the screws back the way you mentioned in your comment? Did it work?ģ. Did you hear back on your comment from iFixit?Ģ. I can hear the call ringing in the car speakers, I can answer it but after that it's silent.ġ. The phone connects, I have the battery and network status on the screen of my car, I can receive SMS on the car's screen, I can stream music to the speakers but I cannot hear anything while in a call.

#Ifixit a1286 logic board Bluetooth

I anyway ended up following the instructions and all went well except that I am now unable to hear anything while in a phone call connected to the Bluetooth in my car. Unfortunately I forgot to check at dis-assembly which screw goes back where at step 11 so I ended up following the instructions although, I would find it logical that the longer screws are for the top and the shorter ones for the bottom holes, which is what you mentioned also. But sadly after repeated and careful attempts to reseat it, my Touch ID is lost for good. Judging by this experience the Touch ID cable/pins must be insanely sensitive – perhaps one pin was dislodged by a fraction of a millimeter? I can’t say for sure.

#Ifixit a1286 logic board how to

Even after I re-opened the phone two more times and finally figured out how to properly reseat the bracket, Touch ID was gone. I finished the battery replacement, and put the cable back in place only to discover: no Touch ID. This gave me a start but I inspected both parts and they appeared to be fine. In my case, as I carefully used the spudger to release the bracket, the released tension shot the bracket out of the phone and the Touch ID cable popped out of its socket with it.

The front of the bracket is the point of tension that holds it in place. Thank you to that commenter, otherwise am not sure I could’ve done it.īe forewarned: make sure you really really want that new battery or display replacement, because you are VERY likely to lose your Touch ID feature on your phone after taking this step. Luckily there are only very minor nicks (hardly even visible) on the metal. This approach totally worked for me so that I could get the frame lifted just enough to slide in plastic cards and wedges until I could switch over to the plastic opening tools. I knew I might end up scraping the metal but nothing else was thin enough to work. After several failed attempts of using plastic opening tools to wedge between the frame and the phone body, I ended up using an exacto-knife (a Stanley knife) based on another commenters suggestion. After several tries I was able to get a firm attachment, however, the result was that the glass was being pulled up without the plastic rim. I had used packing tape on it to keep the bits from falling apart while I waited for the replacement part, however, the tape limited my ability to use the suction cup for removal.

#Ifixit a1286 logic board cracked

The iPhone XS models also got a 6 out of 10 rating.I was replacing my 5s screen due to a cracked screen. Overall, iFixit gives a repairability score of 6 out 10. Rumor has it that Apple wanted to add reverse wireless charging but canned the feature at the last minute. It’s hard to say for sure that the second connector has been added for bilateral wireless charging - it could be there for many different reasons. Similarly, there are now two battery connectors instead of one. When it comes to things that we don’t know yet, iFixit couldn’t figure out how much RAM there is - Steve Troughton-Smith believes there might be 2GB of RAM dedicated to the camera that you wouldn’t notice on benchmarks.

#Ifixit a1286 logic board pro

Even though Apple and Qualcomm has settled its multi-billion-dollar lawsuits, the modem in the iPhones 11 Pro is still manufactured by Intel. The logic board has the same dual-layer design that was first introduced with the iPhone X. Apple managed to put a third camera by reducing the size of the logic board. In other news, the camera module is much bigger in this year’s new device (as expected).